Residential Electric Utility Pole Installation & Replacement
By: Omar Muhammad
Key takeaways
- ComEd’s standard overhead service wire reaches about 150 feet. When a home or outbuilding sits farther back, a private pole carries power the rest of the way, and the homeowner owns and maintains it.
- Wood poles can last 50 to 70 years, but storms and rot at the ground line often end them early.
- The on-site work usually takes 1 to 3 days. Permits and ComEd scheduling happen before that and are what make the overall timeline vary.
- Most replacements cost between $2,200 and $5,000, with tougher access or extra connections pushing the price higher.
- You can replace an old pole with wood, steel, or composite, or remove it entirely and run the service underground.
Most homeowners don’t give the pole in their yard a second thought until it starts to lean. Then the first question we hear is, “Isn’t that ComEd’s problem?” A lot of the time, it isn’t. If the pole stands on your property and only feeds your house, garage, or workshop, it’s probably a private pole, and keeping it upright is on you.
We’ve handled residential utility pole installation and replacement for homeowners in Cook, Will, and DuPage Counties for years. Below is how we explain it to customers: why poles fail, what the replacement process looks like, how long each part takes, and which permits come into play. No two properties are set up the same way, though, so if your situation doesn’t fit neatly into what’s here, call us and we’ll talk it through.
Who owns the utility pole in your yard?
ComEd owns the wire coming off its system and the meter on your house. Everything past the point where its equipment attaches to your property belongs to you. ComEd’s homeowner guide puts it plainly: when a longer run is needed to reach a home, private property poles or extended service wire may be required, and the customer installs and maintains them.
A private residential utility pole usually means something on the property sits a long way from the road. That might be a house set back on a deep lot, a detached garage or pole barn, a workshop, or a coach house with its own power.
A quick way to tell: if the pole is on your side of the property line and only serves your buildings, it’s likely yours. If it also feeds the neighbors or sits along the street, it’s probably ComEd’s. When you’re not sure, we can confirm it on a site visit before you spend anything.
Why utility pole replacement comes up
A wood pole can stand for 50 years or more, but it doesn’t wear evenly. Most of the damage happens where you can’t easily see it, at and just below the ground line. These are the usual reasons a homeowner ends up needing utility pole replacement.
Storms
Chicagoland storms are hard on overhead lines. High winds put sideways load on a pole that may already be weak at the base. Ice adds weight to the wires. Falling limbs can snap a pole, pull it over, or rip the service wire off the house. A storm is often what turns a slow lean into an emergency.
Rot at the base
Wood poles are treated, but over the decades moisture in the soil wins. Rot starts at the ground line and works inward, so the pole can look fine from the top while the base is going soft. Standing water, poor drainage, and landscaping beds piled up against the pole all speed it along.
Woodpeckers and insects
Woodpecker holes and insect damage hollow out a pole from the inside. A few holes near the top may not mean much. Damage near the base, or a pole that sounds hollow, is worth having looked at.
Worn wire and hardware
Even when the pole is solid, the connections on it age. Loose hardware, frayed or sagging lines, and corroded splices can cause flickering lights, voltage drops, or breakers that keep tripping in the building the pole feeds.
Changes to the property
Sometimes the pole is fine and the house has outgrown it. Electric pole replacement or a new pole can come up when you build a new home or add a garage or workshop, when you need an electrical service upgrade and heavier wire, or when you’re bringing an older setup up to code before a sale or inspection.
Warning signs to watch for
- A lean, or a lean that’s getting worse
- Soft, cracked, or split wood near the ground
- Woodpecker holes or insect damage low on the pole
- Sagging or frayed lines, or loose hardware at the top
- Flickering or dimming lights in the building the pole serves
If a pole is down or a wire is on the ground, stay at least 10 feet away and call ComEd at 1-800-334-7661 first. Don’t try to move anything yourself, even a wire that looks dead.
How private power pole installation works, step by step
The physical work is the short part. Most of the calendar time goes to permits and getting on ComEd’s schedule. Here’s how a typical job runs with us.
- Site visit. A licensed electrician looks at the pole, the hardware, the service wire, and the panel it feeds. We confirm whether the pole is yours, check access for equipment, and talk through whether you want a new pole or an underground run.
- Written price. You get a detailed, pre-approved price before anything else happens. The number you approve is the number you pay.
- Permit. We apply for the electrical permit with your town. How long approval takes depends on the municipality.
- Utility locates and ComEd scheduling. Before we dig, we call JULIE to have underground utilities marked. We also schedule the disconnect and reconnect with ComEd, and their calendar sets the install date.
- Installation day(s). Electrical pole installation usually takes 1 to 3 days on site. We set the new pole, move the service wire and hardware over, ground and connect everything to code, and remove the old pole. Soil, access, and the number of connections decide where in that range your job lands.
- Inspection and power back on. The town inspects the work, ComEd reconnects, and we test the system before we leave.
You’ll be without power to whatever the pole feeds for part of the install. We’ll tell you up front how long to plan for, so you can make arrangements for a sump pump, a fridge in the garage, or anything else that can’t sit without power for long.
Permits, inspections, and working with ComEd
In most Chicagoland towns, replacing or installing a private pole needs an electrical permit and a final inspection. Requirements vary from one village to the next, which is a big part of why we handle the permit ourselves instead of leaving it to the homeowner.
Three parties are involved on a typical job:
- Your town issues the permit and inspects the finished work.
- ComEd disconnects the service before we work and reconnects it once the new pole and wiring pass.
- JULIE, Illinois’ one-call system, marks buried utilities before any digging starts.
We line those up so they happen in the right order. Throughout the job we follow OSHA safety rules and ground and insulate the new installation to code.
If you’re searching for utility pole replacement near me, the utility usually shows up first. That’s the right call for a pole along the street. For a private pole on your own property, you need a licensed electrical contractor who can pull the permit and coordinate with ComEd for you.
Costs and options
What drives the price
Most private utility pole replacements fall between about $2,200 for a straightforward swap and $5,000 or more. Where your job lands depends on how easily equipment can reach the pole (an open driveway versus a fenced backyard), the pole’s height and material, how many buildings and connections it feeds, and your town’s permit fees. We won’t quote a number until we’ve seen the site, because these details move the price more than anything else.
Pole materials
Treated wood is still the most common choice and usually the least expensive. Galvanized steel and composite poles cost more, but they don’t rot or attract insects, and they hold up better to sun and weather over the long run.
Replace the pole or go underground
Compact pole-setting equipment fits through most gates, so a new pole doesn’t have to mean a torn-up yard. If you’d rather not have a pole at all, we can run the service underground instead. Directional boring lets us do that without trenching across your lawn. Underground usually costs more up front. In exchange, there’s no pole to rot and no overhead line for a falling limb to take down.
Plan for what’s next
If you’re considering a standby generator, an EV charger in a detached garage, solar, or battery storage, tell us before we size the new pole and wire. It costs far less to plan for that load now than to redo the service later. Our generator transfer switch page and our post on whether you need a generator are good places to start.
Frequently asked questions
- Who is responsible for a private power pole on my property?
- You are. The homeowner maintains, repairs, and replaces a private pole and all the wiring past the point where ComEd’s equipment connects.
- How long does utility pole replacement take?
- The on-site work usually takes 1 to 3 days. Getting the permit and a ComEd date comes first, and that part depends on your town and the utility’s schedule.
- Do I need a permit?
- In most Chicagoland towns, yes. We pull the electrical permit and schedule the inspection for you.
- Will a storm-damaged pole be covered by insurance?
- It depends on your policy and what caused the damage. Check with your insurance company. We’re happy to document the condition of the pole and the damage for your claim.
- Can I get rid of the pole and go underground?
- Yes, in most cases. We can convert overhead service to underground using directional boring, which avoids trenching across your yard.
Every project is different
No two private poles are set up the same way. The lot, the soil, how far the run is, and what the pole feeds all change the plan, the timeline, and the price. If you’ve got a pole that’s leaning, rotting, or took a hit in the last storm, or you just aren’t sure whether it’s yours, give us a call at (708) 726-3243 or request service online. We’ll come out, take a look, and tell you what you actually need.
You can also read more about our residential utility pole installation and replacement service. Every job is backed by our 10-year workmanship warranty, 5-year parts warranty, and 100% satisfaction guarantee.




